How to Make Your Own Headphone Extension Cable

A headset extension cord is multitudinous and interrelated. Sound systems are used to associated to connect one element of a home sound system to another. Create an interrelated extension to learn basic binding and electronics skills by yourself, and have all that you need to set up the wiring of your own home theater. You just need only three wires to make your headset extension easily at home. One wire transmits the left channel, the other transfers the right channel, and the third into the ground.

Headphone Extension Cable

Method Of Making Headphone Extention Cable

Here you go through all the steps. Follow them carefully and make your own extension cable. CLICK HERE for the best 8 headphone extension cables.

Step 1

Cut down 1/2 inch of insulation from both sides of a three-conductor cable. Cut the three wires inside once they lay bare. Then, plug in the soldering iron.

Step 2

Next, take heat shrink and slip two pieces of it onto the cable. Make sure you place them in the middle so the soldering iron doesn’t cause them to prematurely shrink because of the heat.

Step 3

Unscrew the male and female 3.5mm jacks, revealing the terminals inside. Slide the housings onto the cable. The longest terminal which connects to the ground is the “sleeve”. The middle length terminal which connects the right channel is the “ring”. The shortest terminal that connects the left channel is the “tip”.

Step 4

Later choose a wire and around the 3.5mm male jack’s sleeve, wrap the bare copper whilst wrapping the other side of the wire around the female 3.5mm jack’s sleeve. Then wire the male’s ring to the female’s ring and the male’s tip to the female’s tip.

Step 5

Melt some solder onto the soldering iron. This will check the temperature and help the solder flow.

Step 6

Put the soldering iron under the male jack’s sleeve, and add up a small amount of solder on top of it. As soon as you remove the soldering iron, there should be a shiny joint left behind. Next, solder each wire to each terminal.

Step 7

Wrap any bare copper you can see, attached to the tips and rings of both jacks nicely with good quality electrical tape to block off short-circuits. Screw the housing back onto the jacks.

Step 8

Slide a piece of heat shrink over the housing of each jack and heat them well with the heat gun.

How to Connect Multiple Bluetooth Speakers with One Device

Connect your multiple Bluetooth speakers with one device in just a second. it was not possible to connect your smartphone via Bluetooth to several devices simultaneously. Today, thanks to some applications, this has become feasible.

Such an improvement is very practical. Especially when you are in a group or at picnic places you want to need the music of good quality. Obviously, a single smartphone can’t qualitatively broadcast sound for a group of people.

How to use Bluetooth Speaker in Party Mode?

To start using a party mode, make sure both speakers are turned on. Check that one of the speakers is connected to your mobile device via Bluetooth.

On the speaker that is connected to your device, press and hold the Bluetooth and Volume + keys simultaneously. 

Release these keys as soon as you hear the message “Press the Bluetooth and volume down buttons simultaneously on a second Bose device”.If you want To Connect Wireless Speakers To A Stereo Receiver Click here

On the second speaker, simultaneously press and hold the Bluetooth and Volume – key. Release them when the speaker beeps. 

After 10 seconds you will hear “Party mode” on both speakers simultaneously. Party mode is now activated. You can now listen to music on your two speakers using your mobile device.

  • In the same room or outdoors
  • Make sure that there is no interference between them
How to use Bluetooth Speaker in Party Mode?

How to use in stereo mode

To start with stereo mode use one of the speakers, press, and hold the Bluetooth and Volume + key simultaneously. Just release the buttons when you hear the sound “Stereo mode”. 

You will hear a “Left” indication on the left speaker and a “Right” indication on the right speaker.

Stereo mode is now activated. You can now listen to music on stereo using your mobile device. See the steps above To switch from party mode to stereo mode.

simultaneously press the Bluetooth and Volume  + keys.

  • Just press the Bluetooth button and wait for “Bose speakers unlinked
  • Simultaneously   press and hold the Multifunction button and Volume  + until you hear “Bose speakers unlinked”
  • Press Power to turn off the speaker

Samsung & Dual Audio

Samsung smartphones also have a function that can synchronize two Bluetooth devices (speakers). This is the Dual Audio function. 

It’s more restrictive than other apps in terms of the number of paired devices, but better than Bose and Ultimate Ears because it can connect to any Bluetooth device. 

If you have a Samsung Galaxy S8, S+, or newer, you can take advantage of Samsung’s Bluetooth Dual Audio, which works with most Bluetooth speakers and headphones (Bluetooth 5 is not required).

To activate Samsung Dual Audio, follow these steps:

  • Click on Settings  > Connections > Bluetooth.
  • Tap on the Advanced in the upper right corner.
  • Select Dual Audio and flip the toggle to on.
  • To use Dual Audio, connect your phone with two speakers, two headphones, or one of them, and the sound will be transmitted to both.
  • If you try to add a third, the first paired device will be disconnected.
7.1. Amazon Echo

Amazon Echo can connect to one Bluetooth speaker at a time; Amazon has a list of certified Bluetooth speakers to work with the Echo. To do this with an Echo with a display, like the Echo Show or Echo Dot :

  • Say ” go to settings,” or swipe down from the top of the Eco screen.
  • Select Settings > Bluetooth .
  • The list of available devices will show up.
  • Select the speaker and follow the onscreen instructions.
  • Alexa will tell you if the connection was successful.

You can use the Alexa app if your Amazon Echo doesn’t have a screen.

  • From the menu, tap Alexa Devices, and then choose your Echo device.
  • Click on Bluetooth Devices > Pair a new device.
  • A list of available devices will appear in the app; tap the one you want and it’s ready.

Alternatively, you can say ” Get Connected ” to pair your Echo with the device you most recently connected to.

4 Best gaming mouse for palm grip

Rival 3 Gaming Mouse of SteelSeries

  • Cool prism lightning
  • Core optical gaming sensor for true move
  • Mechanical switches of 60M clicks

Benefits

  • Compatible with Both mouse’s Dongle and Bluetooth
  • Good battery life
  • Very fast sensor
  • Construction is solid

Drawbacks

  • Side buttons are tiny
  • The wheel is hard to scroll
  • The height of the palm end is very low

Redragon M711-FPS Cobra Gaming Mouse

  • Adjustable 5 DPI level
  • 7 RGB lights and programmable buttons
  • Compatible with all versions of windows and mac

Benefits

  • Good quality
  • Easy to switch DPI during gaming
  • Good sensor
  • Side buttons are well placed for quick use

Drawbacks

  • Heavy Weight
  • The scroll wheel doesn’t work properly

HyperX Pulsefire Surge Gaming Mouse

  • 360 degree RGB effects lightning
  • Best Sensor
  • Customization is easy with HyperX NGenuity software

Benefits

  • DPI switch options are good
  • Good for small hand
  • Motion traction is smooth
  • Inexpensive

Drawbacks

  • Software needs improvement
  • It is small for bigger hand

Acer Nitro Gaming Mouse

  • Burst Fire: Button
  • Built-in 7 buttons reduce the use of the keyboard
  • Plug and play

Benefits

  • Very Beautiful Shape
  • Cheap Price
  • Braided cable rather than rubber
  • Buttons are very programmable

Drawbacks

  • Lighting profiles can’t be adjustable
  • Heavy Weight